- 您现在的位置：买卖IC网 > Sheet目录941 > 610002-000 (TE Connectivity)HEAT SHRINK CAP FOR SPLICE 1.1"
CUSTOMER DRAWING
4.3.4.2. Procedure B: Three specimens, prepared and measured in accordance with 4.3.1, shall be conditioned for
1000 hours in a 150 ± 3 ° C (302 ± 5 ° F) mechanical-convection oven in which air passes the specimens at a
velocity of 100 to 200 feet per minute. After conditioning, the specimens shall be removed from the oven,
cooled to room temperature, and tested for tensile strength and ultimate elongation in accordance with
4.3.1.
4.2.1
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
Solvent Resistance: Three specimens, prepared and measured in accordance with 4.3.1, shall be
completely immersed in each of the solvents listed in the applicable section of Table 1 for 24 hours at 25 ±
3 ° C (77 ± 5 ° F). The volume of the fluid shall be not less than 20 times that of the specimens. After
conditioning, the specimens shall be lightly wiped, and then air-dried for 30 to 60 minutes at room
temperature. The specimens shall then be tested for tensile strength and ultimate elongation in accordance
with 4.3.1.
Test Procedures – Finished Caps
Test Assembles: Part D-300-12 shall be used to qualify D-300-08, D-300-12 and D-300-18. Fifty-five
specimens shall be made by connecting two wires, MIL- 16878/4-14; with a suitable crimp connector.
Wires shall be 10 ± 1 inches in length. The caps shall be applied in accordance with Thermofit Assembly
Procedure D-300-08/-12/-18.
Dimensions and Dimensional Recovery: Five specimens, as supplied, shall be measured for dimensions in
accordance with ASTM D 876. The specimens shall then be conditioned for ten minutes in a 200 ± 5 ° C
(392 ± 9 ° F) oven, quenched in water in less than 35 ° C (95 ° F) for at least 30 seconds, wiped dry, and the
appropriate measurements taken.
Insulation Resistance: The specimens shall be immersed to within 3 inches of the lead ends in a water bath
containing 5% by weight of NaCl for a minimum of 30 minutes after which time the insulation resistance
shall be measured between the salt solution and the test leads. The test potential shall be 500 volts D.C.
The readings shall be taken after an electrification time of one minute.
Dielectric Withstanding Voltage: The specimen shall be immersed to within 3 inches of the lead ends in a
water bath containing 5% by weight of NaCl for a minimum of 30 minutes after which time the potential
between the salt water and the test leads shall be raised from 0 to the specified voltage at a rate of 500 volts
per second. This potential shall be maintained for one minute and the voltage reduced to 0.
Temperature Cycling: Fifteen assemblies shall be subjected to 200 cycles. Each cycle shall consist of 20
minutes at 135 ° C (275 ° F) and 5 minutes at 240 ° C (400 ° F) in mechanical-convection ovens with an air
velocity of 100 to 200 feet per minute past the specimens. The specimens shall be subjected to 20 cycles
per day and shall be maintained at 25 ± 5 ° C (77 ± 9 ° F) between test days. After the last cycle, the
specimen shall be cooled to 25 ± 5 ° C (77 ± 9 ° F) within one hour and tested for insulation resistance (4.4.3)
and dielectric withstanding voltage (4.4.4).
Tyco Electronics
305 Constitution Dr
Menlo Park, CA
94025, U.S.A.
TITLE:
CAP, SPLICE ENCAPSULATION
Unless otherwise specified dimensions are in millimeters.
[Inches dimensions are shown in brackets]
Raychem
Devices
DOCUMENT NO.:
D-300-08/-12/-18
TOLERANCES:
ANGLES: N/A
Tyco Electronics reserves the right to
0.00 N/A
0.0 N/A
0 N/A
ROUGHNESS
IN MICRON
amend this drawing at any time. Users
should evaluate the suitability of the
product for their application.
REV:
B
DATE:
31-July-08
DRAWN BY:
M. FORONDA
CAGE CODE:
06090
REPLACES:
D010044
ECO NUMBER:
08-018889
SCALE:
NTS
SIZE:
A
SHEET:
3 of 7
? 2008 Tyco Electronics Corporation. All rights reserved
If this document is printed it becomes uncontrolled. Check for the latest revision.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
61083-043622LF
板对板与夹层连接器 0.8MM B2B PLUG ASSY
610SJR00300E
RES CURRENT SENSE .003 OHM 1W 5%
6113B-ER-375E
MOUNTING HARDWARE FOR 700W
615595-000
B-150-07-S
618529-000
CABLE 20AWG TWISTED
620001N005
D-100-00CS1290
620002-000
D-101-00
620004-000
SOLDERSLEEVE SHIELD TERMINATOR
相关代理商/技术参数
6100020004
制造商:TE Connectivity 功能描述:Cap, Splice Encapsulation 制造商:TE Connectivity 功能描述:DEVICE - Bulk 制造商:TE Connectivity 功能描述:D-300-12CS1108
61-000224-02
功能描述:HS-21/41-1G USB CBL 8FT 制造商:omron automation and safety 系列:* 零件状态:有效 标准包装:1
61-000224-03
功能描述:HS-21/41-2G RS232 CBL 8FT 制造商:omron automation and safety 系列:* 零件状态:有效 标准包装:1
610003
制造商:DRAKA 功能描述:CABLE COAX BT3002 100M
610003-000
制造商:TE Connectivity 功能描述:610003-000
6100030005
制造商:TE Connectivity 功能描述:Cable Accessories Cap 制造商:TE Connectivity 功能描述:D-300-18CS374 - Bulk
610003N004
制造商:TE Connectivity 功能描述:610003N004
610004
制造商:未知厂家 制造商全称:未知厂家 功能描述:CABLE COAX TZC75024 100M